Page Loading...
print friendly Print Friendly
Bogen Communications
HTA250A BOG AMPLIFIER 250 WATT

Mouse over image to zoom, click to enlarge

Description: Bogen® Power Amplifier, Series: HTA, 250 W, 120 V AC, +/-1 dB, 20 Hz to 20 kHz, 90 dB Signal to Noise Ratio, 600 to 50 kOhm Impedance, 19 in L x 11 in W x 5-1/4 in H, Black Oxide

Manufacturer PN: HTA250A

UPC:  76536835017

Kendall Electric Inc PN: 63511

Invoice Description:

HTA250A BOG AMPLIFIER 250 WATT


SPEC SHEET

▸ See All in Audio/Video Amplifiers

 
How Can We Make This Page Better?

Bogen® HTA250A Power Amplifier, 250 W, 120 V AC, +/-1 dB, 20 Hz to 20 kHz, 90 dB SNR

Log In for Pricing and Availability

Note: Lead times are estimates only

 
 

Description

The Bogen HTA Power Amplifier Series are high performance units employing Power MOSFET technology. The unique characteristics of Power MOSFET circuitry make them ideally suited to power amplifier design, providing far superior performance and reliability compared to other types of transistors. They offer higher efficiency, reduced heat, simpler overall design, reduced size and weight. The HTA125A Model supplies 125 W and the HTA250A Model supplies 250 W (RMS continuous output) at less than 0.5% total harmonic distortion from 20 to 20000 Hz. An input signal of only 500 mV is required for full rated output. The input impedances are: high-impedance (50k ohms) unbalanced; Low impedance (500/600 Ohm, balanced or unbalanced) with optional accessory transformer Model TL600. Line bridging can be achieved with optional transformer Model TL100. Residual hum and noise is at least 90 dB below rated output and the output regulation is better than 2 dB from no load to full load. The amps can drive a variety of load impedances. Outputs include 4 Ohm, 8 Ohm, 25 VCT and 70 V. The amplifiers are capable of safely driving any recommended load continuously. The HTA Series amps are thermally protected to prevent damage due to excessively high temperatures. Additional failure-preventive devices include overload limiting, short circuit protection, and a SloBlo fuse.
Bogen® Power Amplifier, Series: HTA, 250 W, 120 V AC, +/-1 dB, 20 Hz to 20 kHz, 90 dB Signal to Noise Ratio, 600 to 50 kOhm Impedance, 19 in L x 11 in W x 5-1/4 in H, Black Oxide

Specifications

 Brand Name Bogen®
 Color Black Oxide
 Dimensions 19 in L x 11 in W x 5-1/4 in H
 Frequency Response +/-1 dB, 20 Hz to 20 kHz
 Impedance 600 to 50 kOhm
 Manufacturer Part Number HTA250A
 PART NUMBER KEYWORDS HTA250A ; 765368350173 ; 76536835017
 Power Rating 250 W
 Series HTA
 Signal To Noise Ratio 90 dB
 Standards/Approvals UL 60065
 Voltage Rating 120 V AC

Features

▪ Input Impedances: 50 kOhm Hi-Z unbalanced, 600 Ohm Lo-Z balanced or unbalanced and 1:1 bridging with optional plug-in transformers
▪ -10dB at 100 Hz Lo-cut filter
▪ Illuminated On/Off power switch and overload shutdown LED front panel
▪ Input level control, slo-blo fuse rear panel
▪ Low cut filter switch Internal
▪ 120 V, 60 Hz, 5.5 A, 520 W at full rated output (Idle 60 W) power requirements
▪ 939.2 BTU/hr thermal emissions (full power)
▪ Electronic overload protection, 7 A slo-blo fuse, thermostat
▪ Three-wire grounded, 300 W maximum auxiliary receptacle (not switched)
▪ Designed for continuous operation at rated power, up to 120 deg F; convection-cooled
▪ Thermal protection and automatic electronic overload protection, Hi-Z unbalanced and Lo-Z balanced or unbalanced input w/ accessory transformer (TL600)
▪ Power MOSFET circuitry
▪ Capable of continuous operation at rated output power
▪ Distortion less than 0.5% THD, 20 to 20000 Hz
▪ Multiple output voltages/impedances available
▪ Automatic overload protection
▪ Less than 0.5%, 20 to 20000 Hz at full rated output total harmonic distortion
▪ 500 mV Hi-Z, 150 mV Lo-Z balanced with optional transformer
▪ 4 Ohm, 8 Ohm, 25 V, 25 VCT and 70 V output loads
▪ Better than 2 dB from no load to full load output regulation

Resources

 Product Data Sheet 
 
Time Zone 
 
 
 

Recently Viewed Products: